> For the complete documentation index, see [llms.txt](https://docs.monogoto.io/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://docs.monogoto.io/private-networks/enodeb/t-and-w-n02008.md).

# T\&W N02008

The [**T\&W N02008**](https://www.twsz.com/en/product/123/513.html) is part of the indoor Pico Cell N020XX series of T\&W. The eNodeB comes in different versions, supporting different LTE bands.

![](/files/B8LeRVumFdavijp8JVkW)

### Quick Navigation

* [Getting Started](#getting-started)
* [T\&W N02008 Configuration](#t-and-w-n02008-configuration)
* [Useful Links](#useful-links)

### Prerequisites

* T\&W N02008
* Mikrotik RB4011 router
* Configuration data to connect the eNodeB to Monogoto cloud\
  \&#xNAN;*Reach out to **<support@monogoto.io>** if you haven't received the config data yet*

## Getting Started

{% hint style="warning" %}
The T\&W N02008 does NOT support Local Break Out (LBO), meaning that all data is going to Monogoto’s cloud before being forwarded to the customer's endpoint.
{% endhint %}

Connect the **Mikrotik RB4011** to your internet router using using an ethernet cable connected to **Port 1**.

Connect the **power cable** of the Mikrotik.

![](/files/z7ihkk2OQ91id5A19swa)

Connect an ethernet cable from the **Mikrotik RB4011** router **Port 2**, to the **WAN port** of the **N02008**.

Connect your **computer to the LAN port of the N02008** to configure the eNode&#x42;**.**

Connect the **power cable** to the N02008.

The **POWER** LED will turn <mark style="color:green;">**green**</mark>.

### Connect your computing to the T\&W N02008

* Open the web browser and enter the IP address of the eNodeB, which is most-likely: `192.168.0.101`
* Login using the username and password: `admin` / `Pico@2018`

{% hint style="warning" %}
Make sure to update your password after the first login.
{% endhint %}

***T\&W User Manual*** \
\&#xNAN;*For detailed documentation about the T\&W N02008, review the **T\&W User Manual***

{% file src="/files/ZYYdSDWyNisSo16GHLOt" %}

## T\&W N02008 Configuration

#### Set Basic Parameters&#x20;

In the N02008 configuration portal, select **Management -> Cell** in the navigation bar.

* Set **S1SigLinkServer** to: `10.201.121.242`
* Set **Duplex Mode** to: `TDD`
* Set **TAC** according to the details received by Monogoto.
* Under **PLMNID**, enable the **PLMNID1** and set it to: `315010`
* Select **Submit** to save the configuration settings

![](/files/DTAe9gqaEqWgK8aTtSto)

Click on **Cell1** and fill out the details below:

* **EARFCNDL**: *Use address received from Monogoto*
* **EARFCNDLInUse**: *Use address received from Monogoto*
* **FreqBandIndicator**: *Specify the LTE band you would like to use*

![](/files/CGhXTRmSfkC9CTVIUwZ9)

Click on **Cell2** and fill out the details below:

* **EARFCNDL**: *Use address received from Monogoto*
* **EARFCNDLInUse**: *Use address received from Monogoto*
* **FreqBandIndicator**: *Specify the LTE band you would like to use*

![](/files/FKwrSy7I5Ikedg0xyAai)

### Set Network Configuration&#x20;

Go to **Management -> Network** in the navigation bar.

* Select **IP**
* **Create 2 static IP Interfaces**, according to the configuration received from Monogoto (starting with `10.5X`)
* Make sure to **enable VLAN** for both IP addresses

![](/files/2MJBmXZuEx4sMX0RmOqg)

#### Configure the Network Routing&#x20;

Go to **Management -> Network** in the navigation bar.

* Select **Route**
* Create a new static route:
  * Dest IP Address: `10.201.121.242`
  * Dest Subnet Mask: `255.255.255.255`
  * Gateway IP Address: *Use address received from Monogoto*

![](/files/iHnB6MrhVvjbU9EN7yiA)

### Reboot the eNodeB&#x20;

Reboot the T\&W N02008 for the changes to take effect.

* Go to **Management → Factory → Reboot**
* Press **Reboot**

### **Validate the** connection

Select **Management -> Cell**.&#x20;

To validate the successful connection, review **AssocStatus** and **S1Status**:

* The **AssocStatus** should report: `Active`
* The **S1Status** should report: `Success`

![](/files/NQl3TqmZCLseoBNZL3wz)

{% hint style="success" %}
Do you see a successful connection? **Congratulations! Your eNodeB is successfully set up  🎉**
{% endhint %}

## Useful Links

* [T\&W product page](https://www.twsz.com/en/product/123/513.html)
* [T\&W User Manual](https://files.gitbook.com/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F-M0mPxGpottOEfcucXOR%2Fuploads%2FE1sqbU2Wz29HiuZrWfp1%2FT%26W%20user%20manual.pdf?alt=media\&token=08bdc0f0-c101-4f82-86bb-60d873f846c0)